收藏本站
CYCLONE MAX
cable, is used to connect devices of different types together, such as a PC to
a Hub, or a Hub to a Cyclone. At this point it once again becomes necessary
to program the Cyclone with valid IP numbers, the process for which is
described in greater detail in the following section. However, it is important for
the Cyclone and the PCs to have matching Subnet and Gateway IP numbers,
and for each to have a unique IP number on the network. An example of a
setting for above is as follows:
IP Number
Gateway IP
Subnet Mask
PC1
PC2
CYCLONE
Gateway
192.168.100.1
192.168.100.2
192.168.100.4
192.168.100.3
192.168.100.3
192.168.100.3
192.168.100.3
192.168.100.3
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
It is important to briefly touch upon the underlying network architecture, which
can be a 10Mb (Megabit), 100Mb, 10/100Mb, half-duplex, or a full duplex
connection. The details of the underlying network architecture are beyond the
scope of this document, but it is sufficient to note that most modern network
cards, as well as the Cyclone device, have the capability to configure
themselves for the underlying network through the Auto-negotiation
mechanism. Auto-negotiation is performed as soon as a network cable is
connected to the device, and it sets the operating parameters of the device to
match those of the network.
8.4.2
64
Connecting Cyclone-to-PC via an Ethernet cable
In order to connect the Cyclone to a PC directly via an Ethernet cable, you
need to use what is known as a cross-over cable. A cross-over cable, which is
not provided by P&E, is normally used to connect two similar devices such as
a PC to a PC, or a Hub to a Hub. It is a cable that has its receive and transmit
wires crossed over so that the similar devices can effectively communicate
with one another.
With this configuration, it is still important to assign IP numbers to both the PC
and the Cyclone device. Although at first glance it may not seem necessary to
assign a Gateway address in this configuration, the Cyclone was designed to
operate on a network of more than two computers, and therefore it needs to
be programmed with a Gateway address.
Cyclone MAX User Manual
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
D-1723-WH DRAWER SLIDING 16.56X6.31X19.18"
D072-0103 DEV KIT 7 NIMBLE SBC/FUSION7/BB
D10B2 SURGE SUPPR NETWORK BNC
D1U-12-CONC 12V D1U OUTPUT CONNECTOR CARD
D1U-48-CONC 48V D1U OUTPUT CONNECTOR CARD
D1U-52-CONC 52V D1U OUTPUT CONNECTOR CARD
D1U3CS-D-850-12-HC4C DC/DC FRNT END 850W 12V 3.3V AUX
D1U4CS-12-CONC CONNECTOR CARD D1U4CS OUTPUT
相关代理商/技术参数
CYCLONEMAX 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg
CYD01S18V 制造商:CYPRESS 制造商全称:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM
CYD01S18V-133BBC 制造商:CYPRESS 制造商全称:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM
CYD01S18V-133BBI 制造商:Cypress Semiconductor 功能描述: 制造商:Rochester Electronics LLC 功能描述:3.3V, 64K X 18 SYNCH DUAL-PORT SRAM (FLEX18 1M) - Bulk
CYD01S18V-167BBC 制造商:Cypress Semiconductor 功能描述: 制造商:Rochester Electronics LLC 功能描述:3.3V, 64K X 18 SYNCH DUAL-PORT SRAM (FLEX18 1M) - Bulk
CYD01S36V 制造商:CYPRESS 制造商全称:Cypress Semiconductor 功能描述:FLEx36⑩ 3.3V 32K/64K/128K/256K/512 x 36 Synchronous Dual-Port RAM
CYD01S36V_08 制造商:CYPRESS 制造商全称:Cypress Semiconductor 功能描述:FLEx36⑩ 3.3V 32K/64K/128K/256K/512 x 36 Synchronous Dual-Port RAM
CYD01S36V-133BBC 制造商:CYPRESS 制造商全称:Cypress Semiconductor 功能描述:FLEx36 3.3V 32K/64K/128K/256K/512 x 36 Synchronous Dual-Port RAM